Unit shear is the lateral force a shear wall carries per foot of wall, in pounds per linear foot (plf). You calculate it by dividing the shear delivered to a wall line by the length of full-height sheathed wall that resists it, then you compare that number with the tabulated capacity of the sheathing and nailing you chose. The arithmetic is short. The errors come from counting the wrong length, mixing ASD and strength-level values, and losing track of the numbers across wall lines. ShearWise Pro is built to keep that bookkeeping in one place for 1- and 2-story wood buildings, with a free three-report trial.
This guide is for engineers, designers, drafters and builders working on light-frame wood projects in California, Oregon, Nevada and the Bakersfield area. It gives you the formulas, three worked examples, and the code changes that matter on current West Coast permits.
TL;DR
- Unit shear (v) is the lateral shear per foot of wall, expressed in plf. Demand is the line shear divided by the effective length of full-height segments.
- Segmented walls use v = V ÷ Σ(segment lengths). Perforated walls use the adjustment factor Co to reduce capacity for openings.
- Compare demand with the allowable unit shear for the sheathing, nail spacing and framing you specified, then check aspect ratios, hold-downs and drift.
- In California, projects submitted on or after January 1, 2026 fall under the 2025 California Building Standards Code. Oregon's 2025 OSSC became mandatory April 1, 2026.
- ShearWise Pro organizes wall lines, openings, segments, hold-downs, straps, drift checks and PDF reports for these checks.
Table of Contents
- What unit shear means in a wood shear wall
- The basic formula
- Worked example 1: a wall line with an opening
- Worked example 2: several segments in one line
- Worked example 3: ASD required capacity
- Segmented or perforated: choosing the method
- Comparing demand with capacity
- The checks that follow unit shear
- What the codes require in California, Oregon and Nevada
- Where calculations go wrong
- How ShearWise Pro handles this workflow
- Try the calculation on a real project
- FAQ
- Sources
What unit shear means in a wood shear wall
In US wood design, the induced unit shear is the shear per unit length of wall. The IBC defines it as the induced unit shear in pounds per linear foot in its shear wall deflection provision (Section 2305.3, Equation 23-2). The same term appears in the AWC Special Design Provisions for Wind and Seismic (SDPWS), the standard the IBC and the California code rely on for wood shear walls.
Two numbers are always compared:
- Demand: the unit shear induced by wind or seismic loads on the wall line, from the diaphragm above.
- Capacity: the allowable unit shear for the wall construction, taken from code tables, for a given panel type, thickness, nail size and edge spacing.
If demand is at or below capacity after all adjustments, the wall works for shear. If not, you add length, change the nailing, use a thicker panel, or sheathe both sides.
The basic formula
For a segmented wall, the unit shear is the resultant lateral load from the horizontal diaphragm divided by the total length of full-height sheathing. A PDH Library course on segmented walls writes it as v = R/b for a single panel and v = R/(b1 + b2) for a multi-panel wall. The same course notes that openings raise unit shear and a longer wall lowers it.
In plain terms:
v = V ÷ ΣL
- v: unit shear demand (plf)
- V: total shear in the wall line (lb)
- ΣL: sum of the lengths of full-height segments that meet the code's aspect ratio limits (ft)
Only full-height segments count. A section of wall below a window or above a door is not part of ΣL for the segmented method.
Worked example 1: a wall line with an opening
Post-frame guidance from the National Frame Building Association shows the calculation for a wall with an opening: divide the maximum story shear by the building width minus the opening width. Its example takes 3,614 lb divided by (36 ft minus 12 ft), which gives about 151 lb/ft.
Steps to reproduce it:
- Take the line shear: 3,614 lb.
- Subtract the 12 ft opening from the 36 ft line to get 24 ft of effective wall.
- Divide: 3,614 ÷ 24 = 150.6, reported as 151 lb/ft.
The opening matters. Without it, the same load over 36 ft would be about 100 plf. Removing 12 ft of wall raises the demand by half.
Worked example 2: several segments in one line
When a wall line has several segments of the same construction, the line shear is shared so each segment sees the same unit shear. A discussion among practicing engineers citing SDPWS 4.3.3.4.1 gives 6,000 lb over segments of 9, 7 and 4 ft. The total length is 20 ft, so each segment is designed for 300 plf.
This is a rigid-diaphragm shortcut that works because segments of equal construction share the load per foot. It does not apply when segments have different sheathing or nailing. In that case you need to account for the different stiffness of each.
The individual segment forces follow from the unit shear:
- 9 ft segment: 300 × 9 = 2,700 lb
- 7 ft segment: 300 × 7 = 2,100 lb
- 4 ft segment: 300 × 4 = 1,200 lb
Those three sum back to 6,000 lb, which is a quick check on your work.
Worked example 3: ASD required capacity
HUD's panelized wall design example shows the requirement worked backward. The minimum required unit shear capacity is P ÷ (Ω × (l1 + l2)) = 4,600 ÷ (0.5 × (11 + 5)) = 575 lb/ft. Here Ω = 0.5 is the ASD reduction factor and the two lengths are the segments.
That is the number you carry into the sheathing table. You then choose a panel and nailing whose tabulated capacity is at least that value.
Segmented or perforated: choosing the method
The two accepted approaches handle openings differently.
| Segmented | Perforated | |
|---|---|---|
| Which wall counts | Only fully restrained full-height segments | The whole wall, reduced for openings |
| Capacity | V = v × Σbi | Vwall = (v × Co) × ΣLi |
| Opening treatment | Segments are designed with hold-downs at their ends | The Co factor reduces capacity based on opening size |
| Typical use | Walls with distinct, well-anchored piers | Walls with many small openings and continuous sheathing |
For segmented walls, the PDH Library course gives total allowable shear as V = v × Σbi, with tabulated values for one-sided sheathing that are additive for two-sided sheathing.
For perforated walls, AWC defines design capacity as Vwall = (v × Co) × ΣLi, where v is the unadjusted tabulated unit shear capacity and Co is the adjustment factor for openings. The method traces to a 1981 empirical equation by Professor Hideo Sugiyama and was first codified in a 1995 amendment to the 1994 Standard Building Code.
HUD's Appendix A gives the factor as F = (r³ − 2r²) ÷ (1 − r), with r = 1 − Ao ÷ (H × Σli). Total resistance is V = F × L × v. HUD validates the method for light-frame wood walls with a maximum unfactored unit shear capacity not exceeding 1,200 lb/ft.
A practical way to choose: if you can place hold-downs at every segment end and the segments meet aspect ratio limits, segmented is straightforward to check and to explain to a plan reviewer. If the wall has long continuous sheathing with modest openings, perforated can use more of the wall. Our 24 ft worked perforated example and segmented hold-down method walk through both.
Comparing demand with capacity
Once demand is known, you match it to a tabulated allowable value. IBC Table 2306.3(4) lists allowable ASD shear capacities for wood structural panel walls with Douglas-fir-larch or Southern Pine framing in pounds per foot, with nailing and stud-spacing conditions attached.
A multi-story example from the Simpson Strong-Tie engineering blog, following the 2021 SDPWS, shows how this plays out on one wall line. Induced unit shears of 227, 409 and 591 plf at successive levels are matched to 7/16-inch OSB nailing patterns with ASD allowable loads of 336 plf (6:12 nailing), 490 plf (4:12) and 630 plf (3:12). Notice the pattern: the nailing gets tighter as you go down, because the story shear accumulates.

When the perforated method is used, the allowable values shrink by Co. The same example shows reduced capacities of 255, 479 and 676 plf for a wall sheathed on both sides. Each check should read demand against the reduced number, not the table value.
A clean comparison for each wall line includes:
- Line shear from wind and from seismic, and which one governs.
- Effective length ΣL and how it was found.
- Unit shear demand v.
- Chosen sheathing and nailing, with allowable unit shear after adjustments.
- Demand-to-capacity ratio.
AWC's own examples use the same structure. Its errata document shows a 5,520 lb wind reaction checked against 7,518 lb of perforated-wall capacity for 15/32-inch panels with 8d nails at 4-inch edge spacing. Its seismic example uses Co = 0.78 and a 5,365 lb capacity against 4,733 lb of demand.
The checks that follow unit shear
Unit shear alone does not finish a wall. The checks that travel with it:
- Aspect ratio. The IBC limits height-to-width ratios because tall, narrow segments perform poorly. A segment that fails the ratio cannot be counted in ΣL.
- Hold-down forces. Overturning at segment ends sets the hold-down size. For perforated walls, AWC and Simpson's example note that collectors are designed for v-max and the bottom plate is anchored for uniform uplift equal to v-max.
- Transfer straps and collectors. Forces need a path across openings and into the wall below.
- Deflection and drift. Wood-frame deflection is determined per SDPWS, and Equation 23-2 uses induced unit shear, wall length, height, end-post area, panel rigidity, nail slip and anchorage elongation. Our shear wall deflection guide works one through.
- Sheathing details. Panel grade, blocking and nailing govern the table value. See our 2026 sheathing code guide.
Openings are where many designs go wrong, because every window you add shortens ΣL on that line. Our window opening shear design steps and pier design checks cover that. The same awareness applies in remodels, where taking out a wall starts with knowing whether it carries load and whether it is part of the lateral system.
What the codes require in California, Oregon and Nevada
The unit shear formula does not change by state. The loads that feed it, and the code edition that sets them, do.
California. The 2025 California Building Standards Code was adopted in the 2024 triennial cycle. The Division of the State Architect's published list of changes includes an amendment to CBC 1617.12.8 clarifying that the exemption from load combinations with the overstrength factor applies only to light-frame construction braced entirely by wood light-frame elements, including diaphragms and shear walls. Nevada County, California states that projects submitted on or after January 1, 2026 must be designed to the 2025 code, and that the whole county is now in Seismic Design Category D. An engineering firm's review of the cycle reports that California's adoption of ASCE 7-22 changes seismic and wind inputs and load combinations, so small shifts in base shear can change the shear wall layout you need.
Oregon. Clatsop County lists the 2025 Oregon Structural Specialty Code as effective October 1, 2025, with a six-month phase-in and mandatory use from April 1, 2026. Errata and interim amendments, including new snow load provisions for repairs and alterations, apply too.
Nevada and Bakersfield. Adopted editions and local amendments are set by each jurisdiction. For a Bakersfield project, confirm the edition and any local amendments with the building department in Kern County or the City of Bakersfield before you fix design loads. In Nevada, do the same with the jurisdiction that will issue the permit.
The habit that protects you in all three states is to record the code edition and load basis on every calculation sheet, so a reviewer can see which cycle you designed to.

Where calculations go wrong
Most unit shear corrections in plan review come from a short list:
- Counting a segment that fails the aspect ratio limit.
- Using a table value without applying the adjustments the footnotes require. See our note on the 0.92 SDPWS footnote.
- Forgetting that wind and seismic can govern different lines. Our combined wind and seismic guide shows how to track both.
- Mixing ASD and strength-level values in the same check.
- Changing a window in the architectural set and not updating ΣL.
- Adding hold-downs at every segment when a different layout would need far fewer. We show one such case in cutting hold-downs from six to two.
None of these are conceptually hard. They are bookkeeping failures, and they multiply as wall lines, stories and revisions pile up.
How ShearWise Pro handles this workflow
ShearWise Pro is an online shear wall calculator and report platform for 1-story and 2-story wood-framed buildings. It organizes wall lines, openings, full-height segments, hold-down forces, transfer straps, roof information and story drift checks in one project, and exports clean PDF reports for permit and review coordination. It is a focused tool for residential wood buildings, not a general-purpose structural package, so the inputs match the questions a shear wall check asks.
In the steps above, that means:
- Line shear and effective length. You enter wall lines and openings, and full-height segments are organized per line.
- Capacity comparison. Demand sits next to the wall construction you chose, so the ratio is visible per line.
- Follow-up checks. Hold-down forces, transfer straps and story drift are part of the same project.
- Reporting. A PDF report you can hand to the reviewer.
You can see how results are laid out in the sample calculations PDF and the validation library.
We built ShearWise Pro around one idea: a residential wood shear wall check should not require a general-purpose structural suite. Unit shear is a simple ratio, but it sits at the center of a chain of checks, and every revision to an opening or a roof changes that chain. Our approach is to keep wall lines, openings, segments, hold-downs, straps and drift together, so a change in one place is visible in the report. For 1- and 2-story wood projects, that focus is what we aim to deliver: faster reports, organized projects and PDFs that reviewers can follow.
Evalin
Try the calculation on a real project
ShearWise Pro offers a Three-Report Trial at $0 for three watermarked reports. After that, Professional Monthly is $29 per month and Professional Annual is $250 per year. You can compare plans on the ShearWise Pro plans page, or read more about the shear wall software for residential wood buildings.
Run one of your current wall lines through the trial and compare the unit shear and capacity check with your own hand calculation.
FAQ
What units does unit shear use?
Unit shear in US wood design is expressed in pounds per linear foot (plf), also written lb/ft. The IBC deflection provision defines it as the induced unit shear in pounds per linear foot. Capacity values in the code tables use the same unit, so demand and capacity compare directly.
How is unit shear different from shear stress?
Shear stress is force divided by area, in psi, and is used for members such as beams and bolts. Unit shear is force divided by wall length, in plf, because a sheathed wall resists load through its length and nailing rather than through one cross-section. Wood shear wall design uses unit shear.
Do openings change the unit shear calculation?
Yes. In the segmented method you divide by the length of full-height segments only, so each opening reduces ΣL and raises v. In the perforated method you keep the whole wall in the sum but reduce capacity with the opening factor Co. Either way, a larger opening means less capacity per foot of the line.
Which code edition applies to my project?
It depends on the jurisdiction and the submittal date. California projects submitted on or after January 1, 2026 follow the 2025 California Building Standards Code, and Oregon's 2025 OSSC became mandatory on April 1, 2026. For Nevada and Bakersfield, confirm the edition and local amendments with the issuing building department.
Sources
- Shear Wall Deflection, UpCodes (IBC 2305.3)
- Post-Frame design guidance, NFBA
- Segmented and Perforated Shear Walls, PDH Library
- Summing Shear Wall Lines, Eng-Tips
- Appendix E Design Example, HUD
- Appendix A Methods for Analysis of Shear Wall Resistance, HUD
- Perforated Shearwall Design, AWC
- Errata to the 2015/2018 Structural Wood Design Examples, AWC
- IBC Table 2306.3(4) Wood Structural Panel Shear Walls
- Wood Shear Wall Design Example, Simpson Strong-Tie
- 2025 Title 24 California Code Changes
- 2025 Building Codes and Design Criteria, Nevada County, CA
- Codes in Effect, Clatsop County, OR
- What California's 2026 Building Code Changes Mean for Structural Engineering, ISE Engineers
- Removing a load bearing wall

