In a wood-frame building, drift compatibility means the calculated story drift under design earthquake forces stays within code limits. It also means that everything attached to or supported by the lateral system can follow that movement without losing its job. A shear wall can pass its strength check and still fail this test. This guide covers the ASCE 7 check, the diaphragm assumptions behind it, the connection details that tend to get missed, and a workflow you can apply to 1-story and 2-story residential projects in California, Oregon and Nevada.
If you landed here searching for the Pacific Rim concept, this is a different subject: structural engineering for light-frame wood buildings.
TL;DR
- Drift compatibility has two parts: calculated story drift must stay under the ASCE 7 limit, and gravity framing, connections and finishes must tolerate that movement.
- ASCE 7-22 §12.12.1 requires the design story drift not to exceed the Table 12.12-1 allowable at any story. For qualifying buildings of four stories or less in Risk Category I or II, the limit is 0.025 times the story height.
- Check drift at each wall line, not only as a story average, and confirm the diaphragm is really flexible before you rely on tributary-area distribution.
- Tie-down rods, straps and hold-downs add vertical movement. Include their elongation, bearing deformation and shrinkage take-up in the drift picture.
- Keep a clear record of each assumption so the plan reviewer can follow your drift check.
Table of Contents
- What drift compatibility means in a wood-frame building
- Why drift matters for light-frame wood
- The ASCE 7 story drift check
- Diaphragm behavior decides how you distribute drift
- Check each wall line, not just the story
- Detailing connections so they survive the drift
- Requirements in California, Oregon and Nevada
- Mistakes that produce a false pass
- A drift-compatibility workflow for 1- and 2-story homes
- Perspective
- Run your drift checks in ShearWise Pro
- FAQ
- Sources
What drift compatibility means in a wood-frame building
Story drift is the relative lateral displacement between the top and bottom of a story. Strength tells you whether a wall can carry its shear. Drift tells you how far the building moves while it does.
One official seismic design guideline states the idea plainly: calculated drift must be compatible with the vertical load-resisting elements. Framing and connections that are not part of the lateral system must keep supporting dead and live loads while the building deforms during an earthquake.
In practice, "compatible" covers several things:
- Shear walls and their hold-downs reach the design drift without losing capacity.
- Posts, beams, headers and their connections keep carrying gravity load at that drift.
- Interior walls, partitions, ceilings and cladding can accommodate the movement. ASCE 7 conditions its higher drift limit on exactly this.
- Elements in the perpendicular direction, such as a new lateral element fixed at its base, can tolerate drift in the other direction.
Why drift matters for light-frame wood
Wood buildings are light and flexible, and their lateral systems depend on many small connections. A peer-reviewed earthquake study found that a large share of structural and nonstructural damage to light-frame wood homes is related to excessive lateral drift. The same paper cites a 2% FEMA drift limit for life safety and a 1% limit for functional performance.
That is why a drift check belongs next to the strength check, not after it. A wall line with plenty of shear capacity can still be too flexible if it has long openings, light sheathing or a soft hold-down.
Load path matters too. ATC explains that wood diaphragms transfer seismic forces to shear walls or frames, and that diaphragms, walls, foundations and their interconnections all need enough strength and stiffness for a continuous load path. Stiffness is what drift measures.
The ASCE 7 story drift check
The code requirement is short. ASCE/SEI 7-22 §12.12.1 says the calculated design story drift, determined under §12.8.6, §12.9.1 or §12.9.2, may not exceed the allowable drift in Table 12.12-1 at any story.
For buildings of four stories or less whose interior walls, partitions and ceilings accommodate the design drifts, the same source gives these allowable values:
| Risk Category | Allowable story drift |
|---|---|
| I or II | 0.025 hsx |
| III | 0.020 hsx |
| IV | 0.015 hsx |
Here hsx is the story height below level x. A typical residential project is Risk Category II, so a 10-foot story (120 inches) allows 3.0 inches of design story drift. That is the amplified, design-level displacement, not the elastic displacement from a strength-level analysis.
The amplified displacement is Δ = Cd·δxe/Ie. Using the unamplified elastic displacement is one of the most common ways to pass a check that should fail. Our posts on verifying story drift limits and the Cd deflection amplification factor for wood shear walls walk through the arithmetic.
ASCE 7-22 is the loading standard that the model codes reference. ASCE notes that it is adopted by reference into the IBC, IEBC, IRC and NFPA 5000, so the same drift provisions reach your project through whichever state code applies.

Diaphragm behavior decides how you distribute drift
Before you can check drift at a wall line, you need to know how the roof or floor diaphragm shares force among walls. NIST's guidance on wood diaphragms frames the sequence: establish whether the diaphragm is flexible, rigid or semi-rigid, then analyze accordingly. Flexible analysis can use tributary-area distribution when ASCE 7 criteria are met. Otherwise you calculate diaphragm stiffness and deflection or use a semi-rigid analysis.

Flexible by the code
WoodWorks summarizes two routes to a flexible classification:
- ASCE 7 §12.3.1.1 permits wood-panel diaphragms with no more than 1½ inches of nonstructural topping to be idealized as flexible when each vertical-resistance line meets the seismic story-drift limits.
- Under §12.3.1.3, a calculated flexible classification is permitted when the maximum simple-span diaphragm deflection is more than twice the average story drift of the adjacent supporting walls. The same WoodWorks page covers both.
Notice the first route depends on drift. You cannot assume the diaphragm is flexible and then skip the drift check; the check is part of the justification.
Rigid and semi-rigid
WoodWorks explains that rigid distribution uses the relative stiffness of the vertical elements, while semi-rigid distribution uses the relative stiffness of the diaphragm and the walls and includes diaphragm shear and flexural deformation. The result changes force distribution and the drift each line sees.
Open-front conditions
Garage fronts and large glazed walls create open-front buildings. For loading parallel to the open side, WoodWorks states that semi-rigid or rigid modeling is required, and edge drift, including torsion and accidental torsion, must stay within the ASCE 7 allowable. The drift calculation includes diaphragm shear and bending deformation and uses strength-level forces amplified by Cd. Flexible analysis does not fit because it cannot transfer torsional forces.
Torsion is a common trigger for extra work. See our torsional irregularity workflow for wood for how the 1.2 and 1.4 thresholds come into play.
Check each wall line, not just the story
A story average hides a soft wall line. NIST recommends applying the code drift limits at each shear-wall line when tributary-area analysis is used, instead of only to the story as a whole. Its engineering perspective is that local force resistance together with line-by-line drift checking generally performs better than relying on whole-story averages, especially where wall stiffness varies or torsional irregularity is significant.
For a typical 2-story house, that means:
- Compute drift for each wall line at each story, using that line's own stiffness, openings and hold-down movement.
- Compare each result with the Table 12.12-1 allowable for the story height.
- Look at the worst line, not the average.
- Re-run the check if you change sheathing, nailing, segment lengths or hold-downs.
This is repetitive work when done by hand across many wall lines, openings and full-height segments. It is also where a mistake in one line gets buried in a spreadsheet.
Detailing connections so they survive the drift
Passing the number is half the job. The other half is making sure the elements that move with the building keep working.
Gravity framing and perpendicular movement
The guideline cited earlier says to keep dead and live load support in non-lateral framing and connections under expected seismic deformation. For new base-fixed lateral elements, it calls for designing for the perpendicular-direction drift, and it assumes 3% where there is no full-building analysis. Treat that as one jurisdiction's retrofit guidance, and confirm what your own plan reviewer expects.
Continuous rod and cable tie-downs
Tie-down systems add vertical movement that raises wall drift. A California ICC Tri-Chapter policy on continuous rod or cable tie-downs requires calculations showing that shear-wall drift and applied loads transfer through every anchorage component to the foundation or rigid base.
The same policy limits the total vertical movement between continuous tie-down connectors or restraints to 0.2 inch under ASD. That total counts rod or cable elongation, bearing-plate grain deformation, shrinkage-compensation take-up and other resisting components. The limit may be exceeded only when drift and CBC §1604.4 compatibility are demonstrated considering all sources of vertical displacement.
Our guides to continuous rod tie-down systems and hold-down rods in multi-story wood buildings cover the design and inspection side. For chord sizing under uplift, see designing wood shear wall chords.
Finishes and attached components
Table 12.12-1's 0.025hsx value assumes interior walls, partitions and ceilings that can accommodate the drift. Coordinate with the architect on gypsum board details, stair and cabinet attachments, and exterior cladding so the assumption is true on the drawings.
Requirements in California, Oregon and Nevada
All three states build on the ASCE 7 drift framework through their adopted building codes, so the Table 12.12-1 check is the common core. State amendments and local practice add detail.
California. The 2025 CBC allows wood design by ASD, LRFD, conventional light-frame provisions, AWC WFCM or ICC 400 log provisions, as applicable. California's 2025 code-change material also states that the overstrength-factor load-combination exemption is limited to light-frame construction braced entirely by wood light-frame construction, including diaphragms and shear walls. Bakersfield projects follow the CBC, and the city or county plan reviewer is the one to ask about local checklist items. Our California lateral force resisting systems guide and the post on common lateral design challenges on California projects go deeper.
Oregon. Oregon's Statewide Alternate Method No. 15-01 for cross-laminated timber shows how drift is treated in a state document. It requires the moderate-ductility CLT shear-wall system to meet OSSC serviceability requirements and ASCE 7 Table 12.12-1 drift limits. In Seismic Design Categories D through F, every non-SFRS structural component must also satisfy ASCE 7 §12.12.4 and AWC SDPWS §B.2 Item 4. That method covers CLT, so for conventional light-frame work use it as context, not as your governing rule.
Nevada. Confirm which code edition the local jurisdiction has adopted and whether it has amendments, then apply the ASCE 7 drift provisions that edition references.
Wind can govern in some locations, and a drift check still applies to the seismic side. Our post on combined wind and seismic design for wood shear walls explains how to keep both load cases straight.
Mistakes that produce a false pass
NIST's guidance and WoodWorks' diaphragm material point to the same group of errors. A wall can look adequate in strength while the building or its components are incompatible with the movement.
- Averaging. Checking only average story drift instead of each wall line or diaphragm edge.
- Assuming flexibility. Treating every wood diaphragm as flexible without meeting the ASCE 7 criteria.
- Skipping deformation sources. Ignoring diaphragm shear and bending deformation, torsion, accidental torsion or wall stiffness.
- Wrong displacement. Comparing a strength-level or unamplified displacement with the limit, when the limit applies to the amplified design drift.
- Missing connection movement. Leaving out connection elongation, shrinkage, bearing deformation, gravity framing, partitions, cladding or perpendicular-direction movement.
WoodWorks' guidance makes the underlying point: strength adequacy alone is not enough. Diaphragm classification, wall stiffness, torsion and edge drift all change force distribution and compatibility demands.
A drift-compatibility workflow for 1- and 2-story homes
- Set the basics. Record risk category, seismic design category, story heights and the governing code edition.
- Lay out wall lines. Define each line, its openings and its full-height segments.
- Classify the diaphragm. Document why it is flexible, semi-rigid or rigid, and handle open-front conditions separately.
- Design for strength. Size sheathing, nailing, chords, hold-downs and transfer straps.
- Calculate design story drift. Apply Cd and Ie, and include hold-down and tie-down movement.
- Compare line by line. Check every wall line against Table 12.12-1 at every story.
- Check torsion. Include accidental torsion and test for irregularity.
- Review compatibility. Confirm that gravity framing, finishes and attached components tolerate the drift.
- Package the result. Put assumptions, results and wall-line data in a report the reviewer can follow.
Perspective
Most drift problems we see in residential wood projects are not about a hard equation. They come from inputs that drift apart across a project: a wall line edited in one place, a hold-down changed in another, a roof update that never reaches the drift check.
That is why we built ShearWise Pro around one narrow job, 1-story and 2-story wood-framed buildings. When wall lines, openings, full-height segments, hold-down forces, transfer straps, roof information and story drift checks live in one project, a change in one place is visible everywhere else. We think a focused tool suits this work better than general-purpose structural software that has to cover every building type.
The PDF report matters as much as the calculation. A plan reviewer should be able to see your assumptions and your wall-line results without a phone call. We design the output with that reader in mind.
Evalin
Run your drift checks in ShearWise Pro
ShearWise Pro is an online shear wall calculator and report platform for engineers, architects, designers, drafters, contractors and builders working on 1-story and 2-story wood-framed projects. It organizes wall lines, openings, full-height segments, hold-down forces, transfer straps, roof information and story drift checks, and exports clean PDF reports for review coordination.
You can start with the free trial of three watermarked reports, which costs $0. After that, Professional Monthly is $29 per month and Professional Annual is $250 per year. See the plans and trial details, sign up to try ShearWise, or browse the validation library of calculation examples first. You can also read more about our shear wall software for residential wood buildings.
FAQ
What does drift compatibility mean for a wood-frame building?
It means the calculated design story drift is within the ASCE 7 limit, and the structure that is not part of the lateral system can still carry gravity loads at that drift. Connections and attached components must also tolerate the movement. Both halves matter for a complete check.
What is the allowable story drift for a typical wood-frame house?
For Risk Category I or II buildings of four stories or less that meet the interior-finish condition, ASCE 7-22 Table 12.12-1 allows 0.025 times the story height. Risk Category III is 0.020 and Category IV is 0.015. The comparison uses the amplified design story drift.
Do I check drift for the whole story or each wall line?
Check each wall line. NIST recommends applying drift limits at every shear-wall line when tributary-area analysis is used, because a story average can hide a flexible line. Open-front and torsionally irregular buildings need particular care.
Does hold-down or tie-down movement affect drift?
Yes. Rod elongation, bearing deformation and shrinkage take-up all add vertical movement at the wall ends and increase drift. California's ICC Tri-Chapter policy for continuous tie-downs sets a 0.2 inch ASD limit on total movement unless compatibility is demonstrated.
Sources
- Seismic Design Guidelines, City of Beverly Hills
- Assessment of Wood Residential Construction Subjected to Earthquakes
- ATC, Seismic Response of Wood-Frame Construction
- ASCE/SEI 7-22 §12.12.1, ASCE AMPLIFY
- ASCE 7-22 overview, ASCE
- NIST, Seismic Design of Wood Light-Frame Structural Diaphragm Systems
- WoodWorks, Classifying Wood Diaphragms as Flexible or Rigid
- WoodWorks, Cantilever Wood Diaphragm Webinar Series
- WoodWorks, Diaphragm and Shear Wall Flexibility
- ICC Tri-Chapter TUCC Policy 12, Continuous Tie-Down Systems
- California Building Code 2025, Chapter 23 Wood
- California 2025 Code Changes, Chapters 16 and 16A
- Oregon Statewide Alternate Method No. 15-01

